#Pir mp alert pdf how to#
#Pir mp alert pdf install#
#Pir mp alert pdf serial#

As you walk through the detection pattern, the sensor LED will light for 3 seconds to indicate each alarm detection. The 10 minute walk test mode begins after power up, and can be restarted by removing and replacing the battery.

Product must be installed within the protected area only.

Product must be tested at least once each year.

FCC part 15, Class B verified IC, ICES-003, Class B verified C-Tick CE SIA-PIR-01 Passive Infrared detector standard features for false alarm immunity.

Do not recharge, disassemble, heat above 212В° F (100В° C), or incinerate. * Battery Caution: Risk of fire, explosion and burns.

Do not use optional swivel mount brackets.

Aim the sensor away from stairways, furniture or other objects that can be climbed on by animals.

#Pir mp alert pdf install#

Install the sensor where animals cannot come within 6 ft (1.8 m) of the sensor by climbing on furniture or other objects.

(0.2 вЂ“ 2.0m/Sec.) Advanced Dual SlopeД¬ondition Power Up Walk Test Indicator LED Blinks once per second (for < 45 seconds) ON for 3 seconds = Loop 1 / Low Sensitivity Alarm Flickers rapidly for 3 seconds = walk test period endedД«efore mounting the transmitter permanently, conduct Go/No Go tests (see control panel manual) to verify adequate signal strength and reorient or relocate the sensor if necessary. Battery Life, years (typical): RF Frequency: Operating Temperature: (for indoor use environment) Relative Humidity, no condensation: Detectable Walk Rate: Temperature Compensation:ДЎ x 3 V, Lithium CR123A / DL 123A / 466 5 345 MHz 14В° to 131В° F (-10В° to 55В° C) 95% max. Solution: Replace the battery within 7 days. Problem: The system displays a вЂњlow batteryвЂќ message.

#Pir mp alert pdf serial#

When prompted for the serial number, activate the sensor (wave a hand in front of the lens) to enroll the sensor. To enroll: connect the battery and wait for power up to end (see LED Indications table). Program the sensor as an вЂњRFвЂќ type (supervised RF) device. Refer to the control panel instructions for programming details. Mounting Height: Hauteur de montage: Altura de la instalaciГіn:Д®nroll the sensor in the control panel prior to its usage in the system. Swivel Mount Bracket Swivel Mount Ceiling Bracket Swivel Mount Bracket w/Tamper High Security Lens Kit Pet Alley Lens Kit Use only left OR right side corner mounting holes.Д¬ONNECT THE BATTERY, ENROLL THE SENSOR, CONDUCT GO / NO GO TEST, AND PERFORM WALK TEST / METTRE LES PILES EN PLACE ,ДETECTION 35' / 11m Wide Angle Animal Immune Lens (P/N 5-532-719-00) See page GO Panasonic CR123A / SENSOR, CONDUCT GO / NO2 for ENROLL THE more information / Duracell DL123A / PERFORM WALK TEST TEST, AND See page 2 for Honeywell 466 more information No / Non / No Satisfactory / Satisfaisant / Satisfactorio WiFi.5800PIR-RES Wireless Motion Sensor - Installation Instructions

WeвЂ™ll start with a basic sketch that will give an output on the serial monitor every time the PIR sensor triggers.Д®SP8266WebServer server(80) //instantiate server at port 80 (http port)

#Pir mp alert pdf how to#

These are covered in a separate PIR sensor article.ДЇor the rest of this tutorial, we will follow this wiring diagram:Д«efore continuing, make sure to read how to use an Arduino IDE to program the NodeMCU. Most modules contain a knob for adjusting sensitivity and a jumper for trigger selection. The NodeMCU pinout guide will help you with the correct pin numbers. Remember that the numbers on the board is different from the numbers used in programming. This pin will go low when the sensor triggers. The OUT pin connects to any digital pin of the NodeMCU. The GND pin, of course, connects to the GND pin of the NodeMCU. Thus, it is safe to connect the VCC pin of the PIR sensor to any of the 3.3V of the NodeMCU. PIR sensor modules will work with both 3.3V and 5V levels. The VCC pin connects to the positive source voltage of any microcontroller board. PIR sensor modules commonly have three output pins: VCC, OUT and GND. The sensor will still work but will only detect persons directly in front of the receiver. Removing the dome reveals the infrared receiver.